Here’s how I fixed up my old Sunburst Strat
I have a Strat that I assembled myself, starting with a body and a nice rosewood neck from Monster Relic. There was nothing wrong with any of the parts; the sunburst finish was well done and reasonably convincing as an early-60s Strat body. But there was a joint in the three-piece alcove that bothered me a bit. But honestly, I was probably mostly tired of the burst. You want to see something new sometimes, right?

The thought then struck me that I should try to emulate the solution Leo and the other guys at the old Fender factory used when they hadn’t quite nailed a sunburst finish. A three-tone sunburst, in particular, can be tricky to get right, given the need to balance all three colors and the transitions between them so they look truly good. When this happened at Fender, they couldn’t simply through away the body, and sanding it down to start over from scratch was far too much trouble.
So, what I did was simply spray over the sunburst with a solid, opaque color. It could be white, black, red, or—why not?—blue. No sooner said than done. Being a thrifty (or perhaps stingy?) pensioner, I bought a can of light blue spray paint from Biltema. Yes, they actually sell a decent cellulose lacquer in a spray can for a mere 69 SEK. It’s the same paint I used on a raw-wood Telecaster body I refinished a year or so ago—one that eventually found a good home with an old friend of mine.
When it comes to original Fender guitars, there are several examples of this method, and if you’re lucky, you can find a nice specimen for a “reasonable price” (under 100,000 SEK). The beauty of it is that, over time, the solid overcoat wears away in places, revealing the sunburst finish underneath. This often happens in patches—mostly in the areas where the guitar naturally sees the most wear and tear.



As for these Fender bodies, they were certainly meticulous about the preparatory work, even though the body was already lacquered. After all, there was no need to apply any additional primer; that step had already been done. But I am convinced that they still fine-sanded the body before the solid color was sprayed on.
Since I wasn’t interested in the oversprayed paint lasting too long—I’m one of those odd types who likes a guitar to look a bit worn, even if it’s been freshly painted—I was rather sloppy with the prep work. I settled for simply wiping the sunburst finish with a slightly damp cloth. The idea was that the oversprayed paint would ware off more easily, thereby saving me years of playing and rough handling.

When it was time for spraying, I fashioned a suitable handle to hold the body, using a scrap piece of wood I had lying around. I screwed it into the neck pocket using two screws of the appropriate length and gauge. They didn’t need to be long enough to go all the way through the wood, but the handle had to be secure enough to allow for easy handling during spraying without risking the guitar body coming loose.
I also pulled out my old tried-and-true “gas mask” to avoid inhaling the harmful solvent from the cellulose lacquer. Well armed with this, I went out into the garden at the back of our house and started spraying. You don’t like to do this indoors, even if you ensure good air exchange and use a face mask. There is a reason why the professionals have proper extraction systems or fume hoods for this kind of work. So outdoors is recommended when the weather permits. The optimum outdoor temperature is between 20 and 25 degrees, and if the outdoor temperature during the day should fall below 15 degrees, you should preferably refrain from outdoor spraying.

It’s also important to hold the spray can at the right distance from the guitar body. Hold it too close, and you risk an uneven finish or runs. Holding it too far away isn’t good either; that can result in a speckled finish if the lacquer’s solvents evaporate too quickly. I’ve found that the ideal distance is roughly 20 to 25 cm.

Since I wasn’t too concerned about achieving a super-durable or flawless finish, I simply used the single can of sky-blue paint I’d bought from Biltema. It was actually enough for 4–5 thin coats over the entire guitar body, which was perfectly adequate for my needs. To be completely honest—and I suppose I should be—the result was actually far better than I’d expected, especially considering I planned to sand it down quite heavily once it had dried.
Depending on the type of cellulose lacquer used, a drying time ranging from one week to four or five weeks is recommended to ensure the finish cures properly. This depends partly on the solvent content of the spray and partly on the amount of plasticizer in the cellulose. If it is completely free of plasticizers, it dries more quickly between coats and is also easier to make crack—a desirable effect if you are aiming for a vintage look during the relicing process. But let’s return to that later.
After spraying was complete, I hung the guitar body by its handle in the garage to dry and cure for a while. When it was time to start giving it a bit of a “beating,” I first soaked several sheets of wet-dry sandpaper of varying grits for a few hours, adding a few drops of dish soap to the water. Ideally, you should soak the sandpaper overnight, but it works just fine after just a few hours. The idea is to try to replicate the kind of wear and tear that months—or even years—of gigging can cause if you aren’t particularly careful with the guitar.
I started by trying to bring the finish to a decent shine. To do this, I used 1200- and 1500-grit sandpaper and worked my way up. The finest paper I could find was 2500-grit, which is extremely fine. At that point, the guitar looked really good, and any sensible person would likely have stopped there. But not Gunnar—obsessed as he was with relicing.

I wanted to try to replicate a chipped and worn finish, so I went back to using slightly coarser sandpaper. But first, I made sure to mount a pickguard on the freshly sanded guitar body; it needs to look good and be intact underneath the pickguard—otherwise, it would feel really strange.
I then started sanding a bit more intensely in the areas where the arm and other parts of the body normally rub against the guitar while playing. Before long, I had sanded through the new blue finish in several spots. Yet I kept going, switching to progressively finer sandpaper. It is important to keep the wet-sanding paper constantly wet. You also need to ensure that paint residue doesn’t build up too much on the paper, as that can cause unsightly scratches… But then again, that was exactly the effect we wanted to achieve, so we continued working on the wear. To create some extra scratches and areas of worn-off paint, I also used a very small, dull chisel. It allows you to create fairly realistic scratches and nicks that look like the result of typical “accidents.”

This process could go on indefinitely, depending on just how worn and aged you want the guitar to look. At this point, I decided enough was enough. You can always go back to sanding and scraping later; the guitar isn’t going anywhere, and you can always remove more finish, but it is much harder to put back what has been scraped off. In that case, you would simply have to start over from scratch and spray on a new coat of paint.

And speaking of paint… I promised to get back to that subject. The paint I used was this one from Swedish automobile parts company Biltema: https://www.biltema.se/bygg/farg/sprayfarger/blank-sprayfarg/sprayfarg-blank-himmelsbla-400-ml-2000054224
Biltema calls it a high-quality NC combo lacquer (I have chosen to interpret “NC” as nitrocellulose). It is easy to work with, and the results can look really good. However, it is difficult to get it to develop distinct cracks. Last time, I managed to produce fine cracking by storing the lacquered body in the freezer overnight after first warming it up with a hair dryer. This time, I tried to achieve the same result by alternating between a hair dryer and cooling spray. Unfortunately, however, that yielded virtually no results.

I suspect that this lacquer simply contains too much plasticizer. That’s great if you want the finish to be durable, but from my perspective—and that of many other guitar finishers—it’s not exactly ideal. Instead, you should probably look for sprays where the manufacturer emphasizes a low plasticizer content or none at all. These lacquers are definitely more expensive, but I assume the results—specifically regarding checking—far surpass what is possible with the Biltema paint.
Gitarrdelar (www.gitarrdelar.se) offers spray paint specifically formulated for this purpose in a range of classic colors used by Fender over the years, as does a company called Gitarrverket (www.gitarrverket.se). And there are others. Just Google “cellulose paint for electric guitar” or something similar, and you’re sure to find plenty of results.
The next time I refinish this—or any other—electric guitar, I’m going to try out some of these other products. And I promise to keep you posted. But until then: happy spraying!
This is truly a work in progress.
